Industry news
Do you really know how to choose a circular saw
2022-10-13
As a professional tool, the circular saw has a wide range of uses. How to choose a circular saw, do you really know how to operate a circular saw?
The choice of circular saw:
4. Wired has greater power and noise than wireless.
5. You can make your own fixtures to fix the objects to ensure your own safety and cutting straight.
Operating instructions of the circular saw:
1. Before starting the electric circular saw, check whether the saw blade is cracked, whether the fastening screw is loose, whether the power cord is plugged in tightly, and whether the switch is turned off.
2. The wood can only be cut after the electric circular saw starts to reach a stable speed.
3. When using an electric circular saw to process wet or knotted wood, the feeding speed should be strictly controlled, and it is strictly forbidden to push or pull.
4. Wear protective glasses, protective masks and earmuffs during operation. Stand on the side of the saw blade, not the front, and it is strictly forbidden to cross the saw blade with your arms.
5. The feeding material should be close to the backing, and no excessive force should be used. In case of hard knots, it should be pushed slowly. When receiving the material, it should not behard pulled by hand after 15cm of the saw blade.
6. Short and narrow materials should be clamped. Large materials exceeding the radius of the saw blade shall not be sawed.
7. The electric circular saw must be equipped with a protective cover to prevent the wood chips from flying and hurting people.
8. When sawing a large material, two people must operate it. The auxiliary operator on the opposite side should grasp the wood with force to prevent the saw teeth from hitting the wood back.
9. It is strictly forbidden to move or brake with a wooden stick before the electric circular saw is completely stopped.
How to Straighten a Circular Saw:
1. The track saw can be directly aligned with the saw road, which is more accurate than the backing. When the profile is used as a backer, the width of the circular saw bottom plate needs to be reserved. If you want to be more precise, you can only adjust it with a dial indicator.
2. Do not start the knife feed and retract the stop action on the wood, that is, start the saw and then feed the knife, leave the wood completely and then stop the machine.
3. Are you sure that the saw blade is 90 degrees perpendicular to the board surface? If you want high precision, it is recommended to buy a good right-angle knife edge ruler and feeler gauge to adjust.
It depends on whether you need to cut the arc frequently. Cutting straight electric circular saws are much more efficient than jig saws. If you cut the curve, the accuracy of the jig saw is much better than that of the electric circular saw. The electric circular saw is difficult to cut the curve. If you are a novice, let's cut off a straight line. It is still a bit difficult to make a curve. You can buy an electric circular saw. I personally think that the jig saw is still not easy to use. The efficiency is not as good as the band saw, and the simple is not as good as the hand saw. And cheap jigsaws are bad, and the jigsaws are basically dusty. Electric circular saws are more useful, and the ones that can be flipped can also be used as table saws, which are more practical.
VIDO is a company that manufactures professional tools, including circular saws and electric hammers. Once the products are produced, they are exported overseas and won unanimous praise from everyone. If you are interested in circular saws or other products, you can contact our company.
The choice of circular saw:
1. Try to choose wireless, 5-inch lithium battery is enough, choose brand-name products, and buy double batteries because this is often used.
2. To make solid wood furniture, choose a 10-inch electric circular saw for thick wood, 7-inch and 9-inch are enough for DIY players. You can choose a miscellaneous brand if you don't use it frequently, learn to adjust it yourself, and the effect is acceptable.
3. Be sure to pay attention to safety. Although electric circular saws are much safer than table saws, I once cut off my own power cord, but fortunately, there was no electricity to myself.4. Wired has greater power and noise than wireless.
5. You can make your own fixtures to fix the objects to ensure your own safety and cutting straight.
Operating instructions of the circular saw:
1. Before starting the electric circular saw, check whether the saw blade is cracked, whether the fastening screw is loose, whether the power cord is plugged in tightly, and whether the switch is turned off.
2. The wood can only be cut after the electric circular saw starts to reach a stable speed.
3. When using an electric circular saw to process wet or knotted wood, the feeding speed should be strictly controlled, and it is strictly forbidden to push or pull.
4. Wear protective glasses, protective masks and earmuffs during operation. Stand on the side of the saw blade, not the front, and it is strictly forbidden to cross the saw blade with your arms.
5. The feeding material should be close to the backing, and no excessive force should be used. In case of hard knots, it should be pushed slowly. When receiving the material, it should not behard pulled by hand after 15cm of the saw blade.
6. Short and narrow materials should be clamped. Large materials exceeding the radius of the saw blade shall not be sawed.
7. The electric circular saw must be equipped with a protective cover to prevent the wood chips from flying and hurting people.
8. When sawing a large material, two people must operate it. The auxiliary operator on the opposite side should grasp the wood with force to prevent the saw teeth from hitting the wood back.
9. It is strictly forbidden to move or brake with a wooden stick before the electric circular saw is completely stopped.
How to Straighten a Circular Saw:
1. The track saw can be directly aligned with the saw road, which is more accurate than the backing. When the profile is used as a backer, the width of the circular saw bottom plate needs to be reserved. If you want to be more precise, you can only adjust it with a dial indicator.
2. Do not start the knife feed and retract the stop action on the wood, that is, start the saw and then feed the knife, leave the wood completely and then stop the machine.
3. Are you sure that the saw blade is 90 degrees perpendicular to the board surface? If you want high precision, it is recommended to buy a good right-angle knife edge ruler and feeler gauge to adjust.
4. In fact, the wood board is deformed after sawing, and the wood itself will also have stress. But another point is that your board is relatively short. The longer the profile is used, the greater the error. The longer board may have an error of more than 0.5mm. So either push up the table saw or change the track saw. If high precision is required, the most ideal is a sliding table saw.
It depends on whether you need to cut the arc frequently. Cutting straight electric circular saws are much more efficient than jig saws. If you cut the curve, the accuracy of the jig saw is much better than that of the electric circular saw. The electric circular saw is difficult to cut the curve. If you are a novice, let's cut off a straight line. It is still a bit difficult to make a curve. You can buy an electric circular saw. I personally think that the jig saw is still not easy to use. The efficiency is not as good as the band saw, and the simple is not as good as the hand saw. And cheap jigsaws are bad, and the jigsaws are basically dusty. Electric circular saws are more useful, and the ones that can be flipped can also be used as table saws, which are more practical.
VIDO is a company that manufactures professional tools, including circular saws and electric hammers. Once the products are produced, they are exported overseas and won unanimous praise from everyone. If you are interested in circular saws or other products, you can contact our company.
RelatedNews
RelatedProducts
